RCH3000: Difference between revisions

From W3AXL Wiki
Jump to navigationJump to search
Line 32: Line 32:
One end of your cat5 run will be plugged in to the back of the RCH3000. Use the already terminated end of an existing cable, or crimp your own. Color code followed doesn't matter, but if you know the T568B standard it'll make things easier on the other end. Once you have a suitable RJ45 end in place, we can move on to the radio side of things. You will be using the J5/6 connectors on the front of the radio TIB, as all the needed signals are brought out to these two ports. '''Note: Motorola uses reverse pin numbering for their RJ45 connectors and has done so since the maxtrac era. Be careful!''' Looking with the locking tab on the bottom, pin 1 is on the right side of the connector.
One end of your cat5 run will be plugged in to the back of the RCH3000. Use the already terminated end of an existing cable, or crimp your own. Color code followed doesn't matter, but if you know the T568B standard it'll make things easier on the other end. Once you have a suitable RJ45 end in place, we can move on to the radio side of things. You will be using the J5/6 connectors on the front of the radio TIB, as all the needed signals are brought out to these two ports. '''Note: Motorola uses reverse pin numbering for their RJ45 connectors and has done so since the maxtrac era. Be careful!''' Looking with the locking tab on the bottom, pin 1 is on the right side of the connector.
{| class="wikitable"
{| class="wikitable"
|colspan=2|'''RCH3000 RJ45 Pin'''||colspan=2|'''Radio DB25 Pin'''
|colspan=2|'''RCH3000 RJ45 Pin'''||colspan=2|'''Spectra/XTL DB25 Pin'''
|-
|-
|1||BSY||23||BSY
|1||BSY||23||BSY
Line 50: Line 50:
|8||DIG-GND||18||DIG-GND
|8||DIG-GND||18||DIG-GND
|}
|}
===Radio Programming===
===Radio Programming===
As far as the radio is concerned, the RCH3000 is just another W9 head. Glancing at the buttons on the deskset, you can see it's basically a standard W9 head with the button layout shifted slightly. (you can even use standard spectra control head buttons to change the labels on the RCH!)
As far as the radio is concerned, the RCH3000 is just another W9 head. Glancing at the buttons on the deskset, you can see it's basically a standard W9 head with the button layout shifted slightly. (you can even use standard spectra control head buttons to change the labels on the RCH!)

Revision as of 17:45, 10 October 2018

Motorola RCH3000
Market All
Release Date unknown
EOL Date unknown

The Motorola RCH3000 is an SB9600 Desk Console for remote control of Astro, MCS2000, and iDEN radios.

Overview

The RCH3000 was intended for dispatch centers or offices where a normal radio control head and microphone would be impractical or would look out of place. The deskset emulates a Model 3 control head for the MCS2000 and iDen mobiles, or a W9 head for the Astro Spectra, Spectra Plus, and XTL5000 radios. Connections are made between the radio and the deskset via a junction box or directly to the radio via an accessory connector. Details about the installation and connection can be found in the installation section or in the manual.

Manual

I've scanned and uploaded the RCH3000 manual as I recently found one and I've not seen it posted anywhere else.

68-81129E92-C RCH3000 Installation & Operation Manual with Schematics

Connection to a Non-Consolette Astro Spectra/Plus/XTL5000

Despite several people's claims to the contrary, you can directly connect an Astro Spectra, Spectra Plus, or XTL5000 W-series radio straight to the RCH3000 with full functionality.

Prerequisites:

  • An Astro Spectra/Spectra Plus/XTL5000 with a standard W-series remote mount TIB, with correct flash for a W9 control head. Low, mid, and high power should all work but they must be W9 radios.
  • An RCH3000 with proper power supply and with the correct config settings as described in the installation manual above.
  • A DB25 male connector, cat5 cable, and an RJ45 termination at one end

Making the Cables

One end of your cat5 run will be plugged in to the back of the RCH3000. Use the already terminated end of an existing cable, or crimp your own. Color code followed doesn't matter, but if you know the T568B standard it'll make things easier on the other end. Once you have a suitable RJ45 end in place, we can move on to the radio side of things. You will be using the J5/6 connectors on the front of the radio TIB, as all the needed signals are brought out to these two ports. Note: Motorola uses reverse pin numbering for their RJ45 connectors and has done so since the maxtrac era. Be careful! Looking with the locking tab on the bottom, pin 1 is on the right side of the connector.

RCH3000 RJ45 Pin Spectra/XTL DB25 Pin
1 BSY 23 BSY
2 BUS- 14 BUS-
3 RX AUD 6 FLT-AUD
4 Mic Hi 12 Mic Hi
5 Mic Lo 11 Mic Lo
6 Aud GND 10 ANA-GND
7 BUS+ 5 BUS+
8 DIG-GND 18 DIG-GND

Radio Programming

As far as the radio is concerned, the RCH3000 is just another W9 head. Glancing at the buttons on the deskset, you can see it's basically a standard W9 head with the button layout shifted slightly. (you can even use standard spectra control head buttons to change the labels on the RCH!)